Ornamental features in brocade are emphasized and wrought as additions to the main fabric, sometimes stiffening it, though more frequently producing on its face the effect of low relief. In Guatemala, brocade is the most popular technique used to decorate fabric woven by Maya weavers on backstrap looms. The purpose of this is to give the appearance that the weave actually was embroidered on. It is a supplementary weft technique, that is, the ornamental brocading is produced by a supplementary, non-structural, weft in addition to the standard weft that holds the warp threads together. Brocade is typically woven on a draw loom. The name, related to the same root as the word "broccoli", comes from Italian broccato meaning "embossed cloth", originally past participle of the verb broccare "to stud, set with nails", from brocco, "small nail", from Latin broccus, "projecting, pointed". Swtrap.Brocade Brocade is a class of richly decorative shuttle-woven fabrics, often made in colored silks and with or without gold and silver threads. Swmib.smiv1 - Brocade Switch Management Information Trap Recipient's IP address in dot notation: 192.168.64.88Īccess host subnet area in dot notation: 192.168.64.0Īccess host subnet area in dot notation: Trap Recipient's IP address in dot notation: SNMP community and trap recipient configuration: Highest previlege matched out of six entries is given to the access.ĪCL check is turned off when all six entries contain '0.0.0.0'.ĪuthTrapsEnabled (true, t, false, f): Each ACL entries also have a flag to set each host-subnet-area to be read-write or read-only.
link fail Link failures (LF1 or LF2 states): The number of times the port achieved Link fail1 and/or Link fail 2 states. According Brocade they are insignificant and have no impact on performance. For example, ACL of '192.168.64.0' allows for access by any hosts that start with '192.168.64' regardless of fourth octet. erotherdisc are actual discards which do not fall into either of the other defined discard frame categories. Host-subnet-area is defined by comparing non-zero IP octets. In addition, there are six ACL (Access Control List) to restrict SNMP get/set operations to hosts under a host-subnet-area. Note that in order for an SNMP Management Station to receive a trap generated by the agent, the adminstrator must configure a trap recipient value to correspond to the IP address of the Management Station. The factory default values for the community strings are: Note that the factory default value for the trap recipient of each community is '0.0.0.0'. The first three communities are for read-write access (rw) and the last three are for read-only access (ro). In addition, there are six communities and respective trap recipients supported by the agent. The default value for this parameter is 0 (disabled). In the context of SNMPv1 and SNMPv2c, this means that a request contains a community string is not known to the agent. O authTraps - should the authentication trap, authenticationFailure, be transmitted to configured trap recipient in the event the agent received a protocol message that is not properly authenticated. By default, this value is set at 0, implying that no swEventTrap is sent. When an event occurs and if its severity level is at or below the set value, the SNMP trap, swEventTrap, is sent to configured trap recipients. O swEventTrapLevel - the event trap level in conjunction with the an event's severity level. The default value is set as "Field Support". O sysContact - the contact information for this system (switch). The default value is set as "End User Premise". O sysLocation - the location of the system (switch) (in MIB-II). The default value is set as "Fibre Channel Switch". O sysDescr - the system description (in MIB-II definition). This command allows 'admin' to change the configuration of the SNMP agent in the switch. Set swEventTrapLevel = 0 to disable trapsĪgtcfgSet - change the SNMP agent configuration Completely seperate from the network config of the console port. The agt* commands are only used to set/show the SNMP configuration. HPE Blog, Austria, Germany & Switzerland.
0 kommentar(er)
